Tại Việt Nam, Hãy liên hệ với chúng tôi Dynisco.info.vn nếu Quý khách cần báo giá chính hãng hoặc tài liệu catalogue, datasheet, manual, bản vẽ, hướng dẫn sử dụng sửa chữa thiết bị Dynisco ECHO-MA4-BAR-R23-UNf-6PN-S06-F18-NTR Melt Pressure Sensors· 2 year warranty and 60 years of Dynisco industry experience· Accuracy better than ±0.5%· TiAlN diaphragm coating is standard· mV/V, 0-10VDC, or mA outputs available· Integral temperature sensor option· Available in configurations that fit most extruder applications· 1.5M, 3M, 5M, 7.5M & 10M psi pressure range capability· Alternative fill model available Operating Principle The Dynisco EchoTM Melt Pressure Sensors are used to make pressure measurements of molten polymers up to 752°F (400°C). These models incorporate a 350?Ohm, bonded foil strain gage Wheatstone Bridge. This proven technology provides an output of 0?3.33 mV/V, & 4?20mA, 05?VDC and 0?10VDC proportional to melt pressure (within the specified error band). Most models include an internal shunt calibration (“Rcal”) function that is used to simulate a signal of 80% of full scale. This eliminates the need for a cumbersome calibrated pressure source when scaling associated instrumentation. Installation Do not remove protective cap until ready to install. Prior to initial installation, verify correct machining of mounting hole per Figure 1. Gauge Plug, P/N 200908, is available for this purpose. Before installing make sure that mounting hole is clear of material. Dynisco Cleaning Tool Kit, P/N 200100, should be used. To prevent galling, lightly coat transducer threads with a high temperature anti?seize material. An adequate seal, in a properly machined and maintained mounting well, is obtained with 100 in?lbs. mounting torque. The maximum torque recommended is 500 in?lbs. The electronics housing should be secured, with the optional mounting bracket (P/N 200941), in an area where the ambient temperature will not exceed 185°F (85°C). (Mounting bracket not supplied with EchoTM models.)Wiring Use shielded cable. Attach cable shield to ground at one end only. NOTE: DYNISCO cable assemblies are constructed with shield wired to transducer mating connector, so do not attach shield to instrument. Output Supply Voltage mV/V 10 Vdc (12 Vdc max) mA 14?36 Vdc Vdc 16?36 Vdc Start?Up Bring system to operating temperature with no pressure. For mA units, remove adjustment access screw and adjust Zero Output potentiometer. For mV/V units, zero adjustment must be handled by downstream indicator. Make sure that there is sufficient “soak time” to assure that any material at the tip of the transducer is molten before extruder drive is started. Removal Transducer should only be removed when polymer is hot and liquid. Wipe tip with a soft cloth immediately. The melt pressure transducer must be removed before using an abrasive material or wire brush to clean the extruder barrel. Clean the mounting well before attempting to reinstall the transducer with Dynisco Mounting Well Cleaning Tool Kit, P/N 200100. Thermocouple Thermocouples ( Type J or K) in a rigid stem are optionally available. The Type J (iron?constantan) and Type K is a T/C junction just behind the flush diaphragm at the tip of the transducer. For the most accurate temperature measurement of the melt stream, use a separate immersion?type thermocouple, such as Dynisco TB422 fixed depth series or (G)RMT adjustable models. The thermocouple assembly can be removed by loosening the set screw on the side of hex assembly and pulling the T/C probe, carefully, straight out, without twisting. Replacement assemblies are available. When installing the thermocouple probe assembly, align the slot with the pressure capillary tube and press into snout until top of probe shoulders flush against snout. Lock in place with set screw.Warranty This Dynisco product is warranted under terms and conditions set forth in the Dynisco Web Pages. Go to www.dynisco.com and click on “Warranty” at the bottom of any page for complete details.
Dynisco ECHO-MA4-BAR-R23-UNf-6PN-S06-F18-NTR Melt Pressure Sensors
Đại lý Dynisco Vietnam phân phối sản phẩm Dynisco ECHO-MA4-BAR-R23-UNf-6PN-S06-F18-NTR Melt Pressure Sensors xuất xứ USA, đầy đủ giấy chứng nhận xuất xứ và chứng nhận chất lượng (CO/CQ) cho tất cả sản phẩm cảm biến áp suất, cảm biến nhiệt độ, đầu dò áp suất nhiệt độ, bộ điều khiển, đồng hồ hiển thị. Hỗ trợ giá tốt nhất cho cả đơn vị thương mại và end user trên toàn quốc. Đặc biệt hỗ trợ hình thức thanh toán trả sau 100% cho nhà máy sử dụng thiết bị Dynisco ECHO-MA4-BAR-R23-UNf-6PN-S06-F18-NTR Melt Pressure Sensors. Liên hệ Dynisco Vietnam distributor Hotline 24/7: 0799.002.356 | email: sales@dynisco.info.vn
Nhà cung cấp | Dynisco Vietnam distributor |
sales@dynisco.info.vn | |
Hỗ trợ 24/7 | 0799.002.356 |
Tags | Cảm biến nhiệt độ áp suất, bộ điều khiển, đồng hồ, màn hình hiển thị, đầu dò áp suất nhiệt độ |